Aircraft Data Analysis

Know Thy Parameters, One by One!

A parameter is a parameter…well not in all cases! This course series is dedicated to the Avionics, Systems, Powerplant, and Flight Operations parametric differences and specifics of each major aircraft model. Each course module is 5 days in length and covers not only the mandatory FDR parameters, but the non-mandatory parameters as well. With our flight sim integrated into each course, you will learn how to visualize the aircraft operation and associated parameters from both a top down and bottom up view, equipping you with additional system awareness for those problematic troubleshooting cases.

A220
Flight Data Analysis
AFD 201

Learn how the A220 IMA, SBAS, FCS application, & DCS parameters provide amazing content and insight into your flight operations environment.

A318-A321
Flight Data Analysis
AFD 202

Why is the accelerometer digitized by the SDAC prior to entering the FDIMU? Understand the relationship between parameters at the system interface level.

A330-340
Flight Data Analysis
AFD 203

Coming soon…

A350
Flight Data Analysis
AFD 204

Coming soon…

A380
Flight Data Analysis
AFD 205

Coming soon…

737 NG & Max
Flight Data Analysis
AFD 208

Coming soon…

747
Flight Data Analysis
AFD 209

Coming soon…

757-767
Flight Data Analysis
AFD 210

Coming soon…

777
Flight Data Analysis
AFD 211

Coming soon…

787
Flight Data Analysis
AFD 212

Coming soon…

E145
Flight Data Analysis
AFD 213

Coming soon…

E170-195
Flight Data Analysis
AFD 214

Coming soon…

ATR 72
Flight Data Analysis
AFD 215

Coming soon…

Gulfstream
Flight Data Analysis
AFD 216

Coming soon…

Bombardier
Flight Data Analysis
AFD 217

Coming soon…

Falcon
Flight Data Analysis
AFD 218

Coming soon…

Learn more about how Flight Data Simulation can benefit your organization.

Learn more about how DAE for Aerospace can benefit your organization

How do I modify my FDR to record more than 25 hours?

You can modify the program pins at the rear of the SSFDR to uptick your recording hours. For example, if you have a Honeywell PN 980-4700-XXX installed, you can alter the ‘ground/open’ discrete wiring at pin 17 & 18 of the SSFDR mating connector to increase your recording capacity.

How can determine the amount of hours recorded by my FDR?

The amount of recorded hours is dependent on a combination of your FDAU wps output and FDR maximum allowable recording speed. If there is a one to one relationship between the two units, i.e. – 64 wps FDAU with a 64 wps FDR, you will record the last 25 hours of flight data. This also applies to the case when the FDAU and FDR are both 128wps, 256wps, or even higher. If there is a mismatch between the FDAU and FDR speed, a small and simple calculation can be made to determine actual flight hour recording capacity. See the figure below for the various possibilities:

How can I determine the speed of my Flight Data Recording system in words per second (wps)?

There are basically 4 ways to determine your speed, with the 4th being a bit more involved. First, the speed should be listed or documented in chapter 31 of your aircraft Maintenance Manual and/or Wiring Diagram Manual. However there are times when for some reason, the required information cannot be found. If this is the case, as a second method, you may reference the CMM or technical specification for your Flight Data Acquisition Unit (FDAU). If you are still unable to find this information, you may contact the aircraft manufacturer for the wps or review your previous FDR download analysis reports. Please keep in mind, the OEM will only know the as-delivered configuration of your aircraft. If there were modifications to your aircraft post-delivery – manufacturer unaware of the changes – youll need to contact us for an analysis of your raw data. Using our software we can determine the wps of your system.

With regard to Flight Data Recorder Systems, what exactly does wps imply? I have noticed this abbreviation in our FDR documentation and in communications with the manufacturer several times:

WPS = words per second. A word (12-bits in length) contains binary data which represents a specific parameter value. Please see figure 1 below. Your FDR records in frames (4 second intervals) and each frame contains 4 sub frames (one sub frame = 1 second). With each second that goes by a specific quantity of words are recorded into memory. If you operate a 64 wps FDR system, you will record 64 12-bit words in one second. The higher the word capacity the more information you can record.

What is a Dataframe Layout (DFL)?

A DFL, also known by the name Logical Frame Layout (LFL), Dataframe Interface Control & Requirements Document, and many other names depending on the manufacturer, is a document which specifies the FDR, QAR, or DAR Parameter Word (location), Recording Speed, Sampling Rate, Bits, and Conversion formulae for your recording system.  

Contact our Team

Contact our Team